Small Block Chevrolet Long Water Pump AC brackets - Tall mounts - These are for applications where there is vertical room, but not horizontal room for mounting the Air Conditioner compressor and alternator. 101L - A.C. Bracket mounts the compressor to the passenger side and bolts to water pump and two intake manifold bolts. Because it does not bolt to heads, most heads may be used except vertical intake bolt manifolds like the VORTEC (see 131R below).  Will clear tall valve covers.  See below for dual or tri carb setup.   Can be used with factory alternator bracket.  Use with the 201L. dimensions   buy 101R - Bracket mounts the compressor to the driver side and bolts to water pump and two intake manifold bolts. Because it does not bolt to heads, most heads may be used except vertical intake bolt manifolds like the VORTEC (see 131R below).  Will clear tall valve covers.  See below for dual or tri carb setup.   Use with the 201R. dimensions buy 103R - Designed for more clearance by moving the compressor forward and the alternator toward the (drivers) side of the car. Use with the 203L.   Use with the 230L.  dimensions buy 130R - AC bracket for passenger side applications.   Designed to give maximum clearance for multiple carbs, fuel injection and other above intake manifold access.  Will bolt to all aluminum heads (even fast burn).   Will work with single accessory bolt cast iron heads if one hole is drilled and tapped in heads.  Will clear 3" center bolts heads and 3 3/4" perimeter bolt heads.  Use with the 230L. dimensions buy 131R - Much like the 101R bracket above except designed to accept vertical intake manifold bolts as used in VORTEC heads.  Use with the 230L.  dimensions buy 120R - Much like the 130R but a higher mount to clear 4 1/2" center bolt valve covers.  Will bolt to all aluminum heads (even fast burn).  Will work with single accessory bolt cast iron heads if one hole is drilled and tapped in heads.  Use with the 220L.  dimensions buy Wide mounts - These are for applications like Corvettes and Camaros where the engine envelope is very low.  Trucks can also benefit from these as the truck engine is mounted high for ground clearance. 134R - A.C. Bracket mounts the compressor to the passenger side and bolts to water pump and two intake manifold bolts. Because it does not bolt to heads, most heads may be used except vertical intake bolt manifolds like the VORTEC (see 135R below).  Will clear tall valve covers.  See below for dual or tri carb setup.   Will bolt to all aluminum heads (even fast burn).  Will work with single accessory bolt cast iron heads if one hole is drilled and tapped in heads.  Will clear 3" center bolts heads and 3 3/4" perimeter bolt heads.  Use with the 234L.  dimensions buy 135R - Like 134R above except for cast iron heads with 5/16" vertical manifold mounting bolts like the VORTEC heads.  Use with the 234L. dimensions buy 123R Like 134R above but does not use head bolt.  Instead the bracket bolts to the third exhaust manifold bolt, so watch for header clearance issues.  Use with the 223L. dimensions buy 119L- This bracket places the compressor on the driver side so that the alternator can be mounted in the original factory (passenger side) location. dimensions buy 137L - If you're adding a driver side compressor and don't need the factory power steering pump bracket this is a convenient low profile alternative.   The bracket bolts to the water pump and head.  dimensions buy 107R - For applications that don't use the on-engine mechanical fuel pump this bracket mounts the AC compressor low on the passenger side of the engine.   This bracket is perfect for narrow frame projects. dimensions buy   Alternator brackets - Tall mounts - These are for applications where there is vertical room, but not horizontal room for mounting the Air Conditioner compressor and alternator. 201R - Alternator bracket mounts the alternator to the passenger side and bolts to water pump and two intake manifold bolts. Because it does not bolt to heads, most heads may be used except vertical intake bolt manifolds like the VORTEC (see below).  Will clear tall valve covers.  See below for dual or tri carb setup.  Use with 101L.  dimensions buy 201L - Like 201R but mounts the alternator to the driver side.   Use with 101R.  dimensions buy 203L - This alternator bracket moves the alternator out to make room for larger intake manifolds.  Use with 103R.  dimensions buy 230L - This alternator bracket will fit all 1969 and newer heads.  Gives plenty of room for exotic intake manifolds and carburetors.  Will clear 3" center bolt valve covers and 3 3/4" peripheral bolt valve covers.   Use with 130R.  dimensions buy 220L - Like 230L but with increased valve cover clearance.   Will clear 4 1/2" center bolt valve covers.  Use with 120R.  dimensions buy Wide mounts - These are for applications like Corvettes and Camaros where the engine envelope is very low.  Trucks can also benefit from these as a truck engine is mounted high for ground clearance. 234L - This bracket is designed for vehicles with tight hood clearance.  Will fit all 1969 and newer heads.  Use with 134R.  dimensions buy 223L - This bracket mounts the alternator on the drivers side.   No extra holes are needed.  There must be access to the third exhaust bolt from front.  dimensions buy 219R - This bracket allows you to use fuelie (or other early model) heads with a late model engine.  The alternator bracket mounts the stock alternator without requiring a bolt in the head.  Great for early heads on later model engines.  dimensions buy 215R - This AC compressor bracket mounts the alternator on the passenger side below the water pump centerline and above the crank centerline.  Great for low profile applications.  Simplifies plumbing above engine.  dimensions buy 214L - This AC compressor bracket mounts the alternator on the driver side below the water pump centerline and just above the crank centerline.   Great for low profile applications.  Simplifies plumbing above engine.  dimensions buy 235R - An bracket to mount the alternator on the passenger side. Mounts on a CSI electric water pump.  Aligns with the belt for use with a long water pump crank pulley.     buy     AC and Alternator Serpentine for reverse rotation long water pumps. The reverse rotation water pump use was between 1989 and 1993 for automobiles and between 1988  and 1995 for trucks.  These brackets require the use of the stock steel pulleys. 305 AC and alternator brackets - Uses head and water pump bolts.  Most iron and aluminum heads are compatible.  Pre 1986 iron heads may require drilling and tapping of one hole.  Will clear 3 3/4" peripheral hole valve covers. dimensions   buy 306 AC and alternator brackets - Similar to 305 above, but for use with Vortec and other 1987 and newer iron heads. dimensions   buy 307 AC and alternator brackets - Low mount wide body systems for hood clearance challenged applications.  High quality Idler pulleys are provided.   Drilling and tapping may be needed for 1969 through 1986 cast iron heads. dimensions buy 308 AC and alternator brackets - Like the 307 but for VORTEC type heads.  dimensions buy 408L - Serpentine power steering pump bracket for serpentine belt systems. buy